Complete and professional auto detailing services

Designed to comprehensively sanitize and clean. Floor mats are expertly cleaned and restored to their factory condition. A commercial grade Stihl vacuum is used throughout the vehicle, including under, around, and between all seats. All remaining interior, high-traffic areas, such as seats and other carpeted areas will be vacuumed extensively. No crumbs, dirt, hair, or other forms of debris will remain at the conclusion of this vacuuming effort. Door jams, door frames, and door hinges to be thoroughly cleaned, removing all forms of dirt, grease, and grime. Door frame rubberized trim will be vacuumed and cleaned as needed to remove sand, dirt, and other ailments. All seats and seat surfaces will be expertly cleaned. Cosmetic, stubborn stains will be agitated with a drill brush and hand shampooed in an attempt to restore these areas to their factory condition. Door panels, trimmed elements, consoles, dashboard areas, cupholders, buttons, navigation screens, knobs, controls, handles, seat belts, seat tracks, etc. will be meticulously cleaned and returned to their factory-new state. Interior glass cleaned to perfection, free of streaks, smears, and smudges. On average this baseline service takes 4.0 hours, but can take longer subject to the overall condition of the interior, including excessive cases of sand and/or pet hair.

Process works to eliminate surface contaminants, completely cleanse exterior, and maximize shine, glow, gloss, and protection of all exterior elements. A rinseless wash using a premium grade solution from Optimum Polymer Technologies is used to properly clean all exterior surfaces safely, without introducing new swirls, scratches, and/or other imperfections. Dirt and debris are encapsulated, lifted, and removed using this solution along with an ultra-premium, Korean made, 70/30 microfiber pad. Approximately eight gallons of purified drinking water, supplied by Jax Mobile Detailing, is used during this process as to avoid adding and leaving behind mineral deposits that typically occur when using hard, unpurified water. All four wheels will be cleaned and coated with a specialty surface protectant to maximize appearance and provide 90 days of protection from road grime, grease, tar, brake dust, and asphalt. All four tires will be degreased and applied with a water-based, matte appearance tire shine, providing ultimate protection and eliminating the slinging of the material across painted panels. Other exterior elements and glass will be thoroughly cleaned. Two coats of a premium grade carnauba spray wax will be applied to all exterior surfaces, potentially providing up to five months of professional strength protection. Finally, a binding polymer monomer agent, called Bead Maker, will be applied to all exterior surfaces that enhance gloss, glow, and shine. On average this baseline service takes 2.5 hours, but can take longer subject to the overall condition of the exterior, including excessive cases of dirt, mud, bug splatter, bird droppings, and/or hard pollen spots.

Cleans, conditions, and restores all carpeted and upholstered areas inside the vehicle as close as possible to their factory-like condition. While a large majority of stains will be removed and improved, there are cases where particular, stubborn stains and other upholstered and/or carpeted imperfections cannot be removed due to the nature and severity of the stains. A commercial grade, heated, carpet extractor from Mytee Corporation is used to shampoo and steam all carpeted floor linings and upholstered seats. The machine expels 210 degree pressurized water into the fibers and then immediately suctions the soiled water back into the machine. A cross-hatch pattern is employed, working vertically and then horizontally, overlapping areas, to maximize consistency and coverage of the procedure. The Mytee Spyder HP 60 is the gold standard in carpet extraction technologies and is guaranteed to leave your carpets and upholstery looking as close as is possible to factory new condition. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline interior detailing service line is selected and completed. On average this add-on service takes 2.0 hours, but can take longer subject to the overall condition of the carpeted and upholstered areas.

Mechanical 2-step approach intended to remove severe paint imperfections. Using a product called 3D One, which is a hybrid compound/polish, with a Lake Country blue polishing pad, this particular polish and pad combo provides more cut and correction outcomes for swirls, scratches, oxidation, etc. Please note while still providing some cut and correction, this procedure is still considered to only be mildly aggressive. Using a microfiber pad and a heavy cut compound would be much more aggressive. I have a tendency to avoid doing this to any vehicle as degrading the gel coat in an attempt to correct can be counter-productive. However, the 3D One / Lake Country application would leave behind no protection. It would have to be followed by application of a product called Uno Advanced (made by Rupes) along with a white Ultra Fine Polishing Pad (also made by Rupes). This specific product, Uno Advanced, is what provides us with 12 months of durable protection. Two passes with the polishing machine, therefore, are required to properly correct, polish, and protect the vehicle's painted surfaces. One and a half hours is needed to prepare the vehicle, i.e., mask off emblems, trim, delicate surfaces, etc. plus roughly 120 minutes per pass with the polishing machine. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline exterior detailing service line is selected and completed. On average this add-on service takes 5.5 hours, but can take longer subject to the overall complexity of the vehicle's panels, trim, emblems, and curvature of the body panel lines.

Mechanical 1-step approach intended to remove minor imperfections, including light swirl marks, scratches, and other imperfections, while creating a durable layer of protection that provides several months of protection against environmental contaminants. Using a product called 3D speed, which is a hybrid compound/polish/wax, with a Lake Country orange polishing pad, the polishing & protection procedure is considered the ultimate one-step process to mildly correct plus protect the vehicle's painted surfaces, as the polishe's formulation includes carnauba wax features. Minor swirls and imperfections will be eliminated but more severe imperfections will not be effectively addressed going this route. While providing strong, durable protection, the full 12 months of protection we'd experience from using Uno Advanced, as referenced in the paint correction procedure above, would not be there. But, the vehicle's paint would be semi-corrected and well protected for at least six months, at the least. One and a half hours is needed to prepare the vehicle, i.e., mask off emblems, trim, delicate surfaces, etc. plus roughly 120 minutes per pass with the polishing machine. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline exterior detailing service line is selected and completed. On average this add-on service takes 3.5 hours, but can take longer subject to the overall complexity of the vehicle's panels, trim, emblems, and curvature of the body panel lines.

Addresses mild to severe cases of mold and algae growth. Mold remediation can be a process. In some situations, additional treatments, at no additional charge to you, may be required to effectively eliminate any growths occurring inside the vehicle. Comprehensive interior detailing begins the process and ensures that as many of the physical symptoms and signs of mold are removed. From there, a diluted mixture called Optimum Assure produced by Optimum Polymer Technologies that attacks and kills organic matter, including the coronavirus, is then used throughout the vehicle to deeply sanitize, treat, and clean all surface areas. Particular attention is paid to deeply concentrated areas of mold presence. Optimally, clients seeking out the mold remediation service line should also evaluate the shampoo treatment service line, as the heated, pressurized water instantly kills the organic bacteria and various extractor attachments, including a crevice tool, allow for the machine to be used in tight, confined space. However, the shampoo treatment is a separate service line altogether and would need to be added to the mold remediation process. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline interior detailing service line is selected and completed. On average this add-on service takes 1.5 hours, but can take longer subject to the overall severity, consistency, and texture of the mold.

Headlight restoration is a unique process. Essentially the multi-step process ruins the headlights but then returns them back to their original state. Requires three steps to properly remove water spots, oxidation, scratches, swirls, and yellowness. First, a coarse 1000 grit sandpaper is applied to the surface to eliminate the imperfections, causing significant damage to the material but simultaneously removing all contaminants and imperfections. This process is then followed by application of 2000 and then 3000 grit sandpaper to smooth out the surface and begin bringing forward a smoother, more translucent appearance. A hybrid compound/polish is then used along with a dense foam polishing pad to effectively remove the 1000 grit sandpaper marks and scratches. This step begins to bring clarity and consistency to the lights, and slowly but surely returns them to their natural appearance. Importantly, the vehicle elements around the headlights will have to be prepared for the work. Additionally, ailments and other contaminants within the headlights will not be able to be removed as they are contained within the material and thus are not exposed to be removed. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline exterior detailing service line is selected and completed. On average this add-on service takes 2.0 hours, but can take longer subject to the overall damage of the headlights.

Water contains mineral deposits that are left behind once the water evaporates. The longer these deposits are left on the vehicle's exterior surfaces the more difficult it is to safely remove them. Mineral deposits can, over time, begin to etch into the vehicle's gel coat and break down its structure, effectively ruining the paint appearance. Removing mineral deposits from painted surfaces and trim requires both a chemical and mechanical approach. Using 3D One, which is a hybrid compound/polish, with a Lake Country blue polishing pad, this particular polish and pad combo provides more cut and correction outcomes for water spots. Please note while still providing some cut and correction, this procedure is still considered to only be mildly aggressive. Using a microfiber pad and a heavy cut compound would be much more aggressive. I have a tendency to avoid doing this to any vehicle as degrading the gel coat in an attempt to correct can be counter-productive. The chemical approach is used for more intricate locations, such as trim, glass, and other plastics while the polishing machine is used for painted panels. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline exterior detailing service line is selected and completed. On average this add-on service takes 4.0 hours, but can take longer subject to the overall damage of the headlights.

Paint contaminants include a variety of organic and inorganic matter, and are notoriously difficult to strip from a vehicle's painted surfaces. Conventional soapy washes, rinseless washes, waterless washes, and power washing have proven to be ineffective in addressing these contaminants, such as grains of dirt, tar, grime, asphalt, pollen, iron, bird droppings, bug splatter, etc. Further, attempting to remove these contaminants with aggressive scrubbing, using a towel and solution, actually causes significant damage to the vehicle's gel coat. Clay bar treatment is a safe and highly effective means for removing these contaminants. Paint decontamination consists of a thorough application of premium, fine-grade clay bar to renew the painted surfaces. However, clay bar treatment can introduce marring to the vehicle's gel coat so the textbook would say one pass with the polishing machine to conclude the clay bar treatment is most proper. Given that, I typically recommend the polishing & protection service line in addition to the stated paint decontamination service line. Please note that this add-on service line can only be completed once either the baseline full detailing or baseline exterior detailing service line is selected and completed. On average this add-on service takes 3.0 hours, but can take longer subject to the overall condition of the vehicle's exterior.